Fiat 500 Replacement Key Fob
It could be time to change the battery if the 500 remote key fob isn't working. If you replace the battery but it isn't working, the problem may be elsewhere.
United Locksmith specializes in the creation of new keys for classic vehicles. We have the tools and components needed for this service.
Dead Coin Battery
A dead battery is the main cause of your Fiat 500 keyfob not locking or unlocking the doors. The key fob comes with an in-built battery that can quickly deplete in the event that it is not frequently used. If your remote started to show signs of weakening like a loss of range or stopped working completely it is likely that the battery is dead.
The battery inside the key fob is held in place by steel retaining clips. If the clips aren't tight, they can cause contact problems that will prevent your remote to receive power. Use a flathead screwdriver remove the retaining clip and remove the old battery. Make sure that the battery you choose to use has the same size, voltage and specification as the original.
Water exposure can also cause the key fob to corrode, or even become damaged. Even a small bath in soapy water may damage the electronic chip inside. Keep your key fob dry.
Water Damage
If your key fob doesn't work correctly, it could be caused by water damage. The rubber seals on key fobs keep them from getting damaged by a small drizzle or splash of water. However, it's important to keep the car keys away from the ocean, washing machine, and even the pool.
The key fob has an electronic chip that transmits an electronic message to the immobilizer system in your car. This is the reason why your 500 can start or lock, however if the chip gets saturated, it won't be able to longer function.
You can clean the internal electronics of your key fob using isopropyl alcohol or an electronic cleaner to determine if they are still good. It is best to replace a key fob if it's submerged in salt water, rather than trying to repair it yourself.
A replacement fob could cost you a little bit however it's much less expensive than paying to have your Fiat 500 towed to a dealer and fixed there! You can also do it yourself with a few simple steps. Just ensure you have the correct battery type before you attempt to open your key fob. You can find step-bystep directions for any car keyfob online.
Faulty Chip
The chip in the key fob communicates to your car's immobiliser unit to ensure your car is only capable of starting when the correct key is inserted. If the chip is damaged, or corrupted, your car won't start, no matter what you do.
A faulty chip can occur due to many reasons, but the most common cause is water damage or an unresponsive battery. Whatever the reason, it is an ideal idea to hand the work to a locksmith who can replace the chip for you swiftly and at a reasonable cost.
If G28 Car Keys does not function after being exposed to water that is clean from the tap or rain, remove the battery. Wipe down the electronic component with a paper towel. If the key fob isn't working it's likely to be to be a damaged chip that must be replaced.
Some people will visit their dealer if they need an entirely new Fiat fob. However, this could be expensive. If you are seeking a cost-effective solution to have your Fiat key fob repaired make sure you contact United Locksmith. We have the equipment and know-how required to repair your Fiat key fob in a quick and professional manner.
Faulty Receiver Module
Fiat key fobs send a signal up to 50 feet to the vehicle, which will unlock and close the doors (and start the vehicle for vehicles with automatic transmissions). There are several reasons why the fob could not function. This includes a dead coin battery, water damage buttons, worn out buttons or a problem with the receiver module and signal interference, or an electronic chip malfunctioning.
If the fob was placed in an area that has experienced severe trauma (such as being dropped on the floor, or washed in a washing machine) the fob may not be in a position to connect with the Body Control Module (BCM) of the car. This is because the BCM is secured and will only accept signals from a genuine original key, and not from any other.
If this is the case, then you will require replacing your fob. A professional locksmith can handle all aspects of the replacement process and can even program a brand new one for the 500. They can even give you the fob cloned to work exactly the same way as the original (and costs just a fraction of what it would cost).